deneme bonusu veren siteler deneme bonusu veren siteler bahis siteleri

Scott Marine Surveyor Blog

Subscribe

Via Email:

Archive



TO THY BATTERIES BE TRUE

Posted On: May 10, 2018

Keep On Charging

It's that little box that keeps the whole show running. Show it the respect it deserves with these simple tips.

Load Testing Your Batteries

On a boat, the easiest way to apply enough load to a battery for a meaningful test is to use the starter motor on the engine as the load. Disconnect the ignition coil, if yours is a gas engine, so the engine won't start up, connect your voltmeter to the battery, and have a friend crank the engine. If the voltage falls below 9.6 volts, you need a new battery.

It Won't Stop Your Heart, But ...

Direct current (DC) might be less likely to shock you than alternating current (AC), but there's a lot more to safety than not getting shocked. DC sparks around charging batteries can cause an explosion. Battery electrolyte is made from sulfuric acid, which can cause severe burns or blindness. DC systems are relatively safe, but still demand your respect and caution.

Don't Let Your Batteries Go Boom

Batteries do go boom from time to time. Explosions involve two things: hydrogen gas and a spark. Hydrogen is the lightest of the elements, so it will disperse quickly if released into a ventilated space. But an explosion could still happen if the electrolyte levels get so low that the plates are no longer covered or, if the vent is clogged, allowing hydrogen to build up. So, be sure your deep-cycle batteries are in a well-ventilated space, check the electrolyte levels regularly, charge it using a marine charger with a regulator, keep grease and other contaminants away from the vents, and watch out for bulges in the battery case, which indicate a buildup of hydrogen gas.

0

I PHONE TAKE A SWIM?

Posted On: May 08, 2018


i can't tell you how many times I see and hear about wet phones.  It can be a very frustrating moment to see your phone drenched with water, but panicking and rushing to dry it with anything that you find is not the solution and may actually cause more harm.

According to Apple, in most cases, you can still save your iPhone after it has been exposed to water, but it’s important that you take the necessary precautions to limit the damage and avoid causing extra harm.

Here’s the process they recommend to deal with an iPhone that has been damaged by water.

Precautions to Take When an iPhone Is Exposed to Water

  • If your iPhone is plugged in to a power source, unplug it immediately as it can cause short circuits. Also, disconnect USB cables, headphones, or any other accessories connected to it by a wire.
  • Completely dry the external surface of the iPhone with a piece of cloth. Avoid using electronic devices for drying, such as a hair dryer.
  • Hold your iPhone upside down and gently shake it to get liquid out of the ports and sockets.
  • If the iPhone is still turned on, power it off by holding down the power button.
  • If your iPhone is in a case, take it off to avoid any liquid being trapped inside.

Now that you’ve taken the necessary precautions to limit the water damage to your iPhone, you’re ready to dry the internals.

How to Dry a Wet iPhone

It’s a popular concept to stuff a wet device into a bag full of rice to dry the internals. Based on experience, this actually works and helps to absorb the moisture within the iPhone.

  1. To get started, grab a plastic zipper-lock bag or anything else that can be filled with rice.
  2. Now fill it with rice and place the iPhone in it so that its entire body is covered by rice.
  3. Leave it there for about 36 hours or more until all the moisture is absorbed by the rice. Be warned that some dust or rice grains may get into the ports.
  4. An alternative option is to use silica gel which is more effective in drying a wet device, but you’ll need lots of them to cover the iPhone.

Once you’ve waited for at least 36 hours and feel confident that the iPhone has dried completely, take it out and try switching on. In most cases, the iPhone will turn on successfully.

If your iPhone doesn’t turn on, then you should take it to a nearby Apple Store and have it inspected. Keep in mind that iOS devices have a liquid contact indicator that shows whether the device was damaged by water, so make sure that you don’t claim that the iPhone stopped working without any apparent reason.

Protect Your iPhone from Water

Not all iPhones will survive a bath, so it’s best to play it safe from now on. You already use a case to protect your iPhone from accidental drops, but why not from water damage? To protect your iPhone from an early demise caused by water, use a waterproof case.




0

CINCO de MAYO

Posted On: May 03, 2018

ITS A FEW DAYS AWAY, BUT WHAT IS IT BESIDES A DRINKING DAY?

Cinco de Mayo—or the fifth of May—is a holiday commemorating the date of the Mexican army’s 1862 victory over France at the Battle of Puebla during the Franco-Mexican War (1861-1867). A relatively minor holiday in Mexico, in the United States Cinco de Mayo has evolved into a celebration of Mexican culture and heritage, particularly in areas with large Mexican-American populations.

In 1861, Benito Juárez—a lawyer and member of the indigenous Zapotec tribe—was elected president of Mexico. At the time, the country was in financial ruin after years of internal strife, and the new president was forced to default on debt payments to European governments.

In response, France, Britain and Spain sent naval forces to Veracruz, Mexico, demanding repayment. Britain and Spain negotiated with Mexico and withdrew their forces.

France, however, ruled by Napoleon III, decided to use the opportunity to carve an empire out of Mexican territory. Late in 1861, a well-armed French fleet stormed Veracruz, landing a large force of troops and driving President Juárez and his government into retreat.

Certain that success would come swiftly, 6,000 French troops under General Charles Latrille de Lorencez set out to attack Puebla de Los Angeles, a small town in east-central Mexico. From his new headquarters in the north, Juárez rounded up a ragtag force of 2,000 loyal men—many of them either indigenous Mexicans or of mixed ancestry—and sent them to Puebla.

In the U.S. the date has become associated with the celebration of Mexican-American culture. In Mexico, the commemoration of the battle continues to be mostly ceremonial, such as through military parades.

0

THE PROPER SIGNALING DEVICES

Posted On: May 01, 2018

   Signal aids are critical to help rescuers pinpoint your boat's exact location in an emergency.

This from the Coast Guard.

 

A boat on the ocean is a small, hard-to-see target in good conditions, and even with all the technological advances in EPIRBs and communications technology that interface GPS information with the VHF radio, nothing can help rescuers get a visual fix on a boat in distress better than a flare or other visual signaling device. The U.S. Coast Guard requires you to carry the proper visual distress signals on board, and it's important to know how to use the different types in an emergency.

Aerial signals: Aerial signals are used to alert all the boats in the area that you're in trouble. They're fired from a variety of self-contained launchers or specifically designed pistols, and can reach an altitude of 450 to 1,000 feet. The combination of bright light and high altitude makes these flares highly visible from a long way off, but most have a relatively short burn time. The U.S. Coast Guard recommends firing two aerial signals-one immediately after the first has gone out-so that in an emergency, rescuers can confirm the sighting and/or the direction of the signal.

Handheld signals Once you've alerted boats in your area that you're in distress and have given rescuers a general idea of your location with aerial signals (and, often, radio or EPIRB contact as well), a handheld signal emits a bright light that will help your rescuers to zero in on your position. In an emergency, your rescuers have seen your aerial signals, confirmed your position on the radio, and use the light from a handheld to steer directly to you.

Smoke signals: Smoke signals are somewhat similar to handhelds in that they are designed to help pinpoint the location of a vessel in distress; they do so by emitting a thick, colored smoke rather than light. They're obviously of no use in the dark, but in daylight, a big plume of colored smoke is often more visible than the bright but relatively small light emitted by a handheld flare. And most smoke flares will float and work on the water.

All pyrotechnic signaling devices must be stored in a cool, dry place, and most are available with a tough, plastic, waterproof storage case. Make sure you keep the signaling kit in an easily accessible location on your boat. And remember: It's illegal to fire a distress signal in a non-distress situation.

 

0

SO YOU WANT TO CATCH FISH?

Posted On: April 24, 2018


IS YOUR BOAT CUTTING YOUR CATCH?

 One important thing you can do to boost your catch rate is to reduce the amount of noise you make. Unfortunately, no matter how careful you are, your own boat may be sabotaging these efforts. Some boats alarm fish more than others. But take heart, savvy angler: once you know about these five common fish-scaring flaws, you can institute corrective measures. Here's how:

  1. Engine Noise

Engines scare fish. But all engines are not equally noisy. The biggest offenders are two-stroke outboards. Particularly when in neutral, they create a real racket. You can hear the clickety-clack of metal parts hitting one another, right? That sound travels through the water, too. In shallow waters and calm conditions, when stealth becomes imperative, the best workaround is to plan your approach to hotspots so you can shut down the engine while it's still in gear, then drift into position.

 

When putting fishing rods in the bed of a pickup to trailer down the road, always lay them with the butt end toward the front of the truck. Laid tip-first, they may break if you have to slam on the brakes and momentum carries them forward.

One of the loudest sounds made below the waterline by most other engines — electric trolling motors included — is prop noise, directly related to prop speed. In other words, slow down. You can significantly cut the level of noise simply by backing off on the throttle. Another noise no-no you create with your power plant is the "thunk" of shifting in and out of gear. Again, this metal-on-metal sound travels well underwater, and fish don't like it. Though I haven't experimented with the new shift-dampening props (such as the SDS by Yamaha) or smoother-shifting stern drives (like the new Mercury 4.5L, which incorporates a new lighter flywheel for smoother shifting), I've observed firsthand how many species flee when boats are shifted into gear.

It's worth noting that in some cases, specifically with large inboard diesels, the deep thrumming of the motor may actually bring fish to your boat. There's more than mere anecdotal evidence to support this claim; according to marine biologist and author Daniel Bagur (Where the Fish Are, International Marine Press, 2009), certain predators are attracted to some long-wavelength vibrations. A few years back, I recorded the underwater sounds made while trolling on a 50-foot sportfish, and I sent the recordings to Bagur. He confirmed that many predators should find the type of sound created by the big diesels swinging large props attractive, as opposed to scary.

  1. Chine Slap

The sound of water slapping against a hull, particularly one with reverse chines, can be so bad for fishing that a few boatbuilders actually design "quiet" chines. Of course, if your boat doesn't have specially designed chines and you can't get a bite while listening to that slap-slap-slap all day long, you're more interested in finding a solution than in what some boatbuilders may or may not do.

Positioning your boat properly is the first step. If you can keep the stern into the seas safely, you'll eliminate the problem to a large degree. But this isn't always convenient, safe, or even possible. Another measure you can take is to weight down the bow a bit. On some boats, moving a full cooler (or an extra angler) onto the bow is enough to completely submerge the offending chines. And on some others, shifting weight to one side or the other will eliminate the slap.

Another trick that works on certain boats (while adrift or at anchor) is to slide a foam pool noodle under the chine, then push it far enough back that water pressure holds it in place. Be sure to tie a piece of fishing line to the noodle and secure it to the boat so it doesn't float away if a wave rocks it free.

You use a fishfinder to spy on the fish, but it may be alerting them to your presence as well. (Photo: Lenny Rudow)

  1. Fishfinders

I know lots of people will say I'm wrong about this (especially the fishfinder manufacturers), but at least some species of fish can hear or otherwise sense your fishfinder — and may even alter course to get away from the pings. Even though many experts disagree, I say this because I've seen it with my own eyes, when I launched a boat rigged with several fishfinders in the quarter-million-gallon habitat tank at the National Aquarium in Baltimore.

While an observer watched from two stories below and we stayed in contact via FRS radio, I tried using the fishfinders in an attempt to differentiate between species. That part of the experiment was a complete failure; I couldn't even tell the difference between a tarpon and a sea turtle. But the surprise lesson was that when the fishfinders were active, some of the fish, and especially the sharks, would go around the boat instead of swimming under it. When all the units were turned off, however, they would swim under the boat without hesitation.

Sure, there are many variables that my less-than-scientific experiment didn't address: power level, transducer frequency, and the artificial environment, for example, could all affect the result. And it stands to reason that in certain situations with certain species, your fishfinder pings could even serve to attract fish rather than repelling them. But the bottom line is this: some fish can sense some fishfinders at least some of the time, and they may even avoid them, so you and I have to consider that a fishfinder may be a potential problem.

  1. Slamming Hatches

While I listened beneath the water's surface with a hydrophone, the loudest of all the potential fish-frightening sounds I heard was a slamming fishbox hatch. The noise created by fiberglass banging fiberglass is akin to a gunshot underwater, and it's certainly enough to scare every living creature within casting distance. Fortunately, this is a fairly easy item to fix. If your boat has a hatch or lid that slams, buy a roll of sticky-back foam rubber at your local marine supply store and make a gasket. Apply it to the offending contact points, and you'll turn that slam into a muted thump.

  1. Electrical Discharge

Some fish can detect even minute amounts of D.C. current, which is harmless to humans. In fact, some species are attracted to certain electrical fields and are repelled by others. There are even a few fishing-tackle manufacturers that have capitalized on this phenomenon by building items (such as the Pro-Troll and the Mako Magnet) intended to bring fish to your boat via electrical discharge. Unfortunately, there's very little reliable science on this subject, and different species of fish seem to react differently to electrical current. Many boats leak a stray electrical current into the surrounding waters, so for all you know, you could be chasing your potential catch right out from under your hull. True, you could just as easily be inadvertently attracting them, but unless you're the marina fishing star, it seems prudent to eliminate all electrical interference.

The safest bet is to test your boat to make sure it's electrically sound. Not only is this good for the fishing; it'll also ensure your running gear doesn't suffer from the corrosive effects of electrolysis. Hook the negative lead of a voltmeter (set to a DC scale of zero to 1 volt, or a scale with tenths of a volt) to the negative terminal of your battery; attach the positive lead to a bare wire. Turn off everything on the boat and lower the wire five or six feet down in the water. Now, turn on your boat's electrical items one at a time while you watch the meter. If it jumps by more than a tenth of a volt, you have a significant electrical leak — and a potential fish problem to deal with. Most of the time, such a leak is due to cruddy connections, bad grounds, and/or bad bonding associated with whatever electrical item causes the voltage change.

Of course, there are other things, aside from your boat, which will still freak fish out. Your own voice at a regular conversational level, for example, can be heard a good 15 to 20 feet below the waterline. Screech like a banshee when you miss a bite and you're going to send the fish scurrying. Even casting a shadow across the water will spook some fish, which live in fear of attack from above via osprey or eagle.

But at least now you know what to do to make your boat less of a fish deterrent — and with a little luck, the next time you hit the water, you'll come home with a full cooler.

 

0

GETTING READY TO FLOAT THIS SPRING

Posted On: April 19, 2018

Every year we all say it — and we all mean it — this was a brutal winter.  

With a rainy spring following our frigid, snowy winter all the elements are present that could lead to sinking your boat.

Nothing ruins a planned day on the water like discovering your boat’s a submarine headed south.

Now that’s not fun for anyone. In an effort to prevent that from happening, here's our spring checklist.

Please, don't overlook even a teeny drip or leak, as a slight bit of wetness can turn into a problem that can be sink-capable if ignored long enough.

 

  •   Check every nook and cranny for water tightness; turn a hose on any spot that looks vulnerable.
  •   Inspect the hull for cracks, blisters, dings, and dents.
  •   Check and replace dried-out caulking around hatches and ports. 
  •   Ensure that thru-hull fittings are not corroded or cracked.
  •   Check engine coolant lines for proper fitting.
  •   Examine all shafts and readjust the stuffing box packing if necessary.
  •   Inspect the muffler and exhaust hose.
  •  Make sure that seacocks work properly and are not frozen open or shut.
  •  Clean debris from the scuppers.
  •   Be sure that the drain plug is properly installed.
  •   Confirm that the intake strainer is secure and corrosion-free.
  •   Replace all cracked or weak hoses for the head and air conditioning.
  •   Before you hook up to the dock’s fresh water system, ensure that fittings, clamps, and valves are tight and that the hose isn’t dried out.
  •   Check all thru-hull bolts, such as those securing the swim platform, speedometer, transducers, and struts.
  •   Check the out-drive unit of an inboard/outboard for damage or leaks.

Before you leave, check that all lines are intact and reinforce them as necessary. Hang out your fenders — you don’t want your boat banging into the dock during spring storms.

Finally, even if you don’t plan to start taking her out until Memorial Day or later, make it a regular practice your to visit your vessel and check the lines and look for signs of dampness.

0

TIPS FOR GETTING MORE OUT OF YOUR SURVEY

Posted On: April 12, 2018

Tips To Get More From A Marine Survey

 

1. If buying a boat, don't rely on an old survey that may not give a current representation of the boat. Insurance underwriters will normally not accept a survey older than six months.

 2. Attend the survey and take the opportunity to ask questions and learn more about your new boat. Most surveyors are happy to talk about what they're finding and what needs to be done to correct any problems. Just don’t be a nuisance, after all, time is money.

3. Don't select a surveyor on price alone; find one that has experience on your type of boat and one with whom you feel comfortable.

4. Boats don't pass or fail a survey. The buyer determines if the boat is acceptable or not, and the insurance company will list what must be done in order to provide coverage.

5. Even a brand-new boat will almost certainly have some recommendations from the surveyor, though most of them should be addressable through the builder's warranty.

 6. Surveys include an approximate current fair-market value for use by lenders and insurance companies. This can serve as a price negotiation tool.

 7. A survey is a useful guide for planning upgrades and repairs and allows you to prioritize your budget.

0

MARINE SURVEY BASICS

Posted On: April 10, 2018

The Basics

 Not all surveys are the same, but they generally begin by describing the boat overall. This part of the survey lists the year, make, model, hull identification number (HIN), and the basic specs of the boat, such as length, beam, and weight.

It should also explain the scope of the survey, which describes the limitations. For example, it may say that hard-to-access areas were not inspected, that electronics were only powered up and not tested, or that engines were not part of the survey. From there, the survey goes into meatier stuff. It will document the condition of structural components, such as hull and deck, running gear, bulkheads, and engine beds. Things like the fuel, plumbing, and electrical systems are inspected and discussed with respect to relevant standards; living spaces are inspected; and safety items are noted, such as the existence — or the lack — of carbon-monoxide alarms and fire extinguishers.

A good survey is more than just an inventory of the boat's equipment. The surveyor will comment on each section of the inspected boat. Finally, near the end of the survey are the recommendations, arguably the most important part.

0